Please follow the steps below to complete your installation of NETePay FDMS Rapid Connect Host EMV - RRH 5.06.16 Rental

Step 1 - Install Client Control

In order to communicate with this NETePay your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.66

Release date: 11/14/2022

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our Compatible devices page.

Release notes for v1.66

  • Support is added for the PAX A35. Also, the PAX IM30 for EVO is released now that we have a full certification for this unattended device. New SecureDevice values listed below...
    • EMV_A35_PAYMENTECH
    • EMV_A35_VANTIV_E2E
    • EMV_A35_TSYS
    • EMV_A35_TSYS_VOLT
    • EMV_A35_RAPIDCONNECT
    • EMV_A35_RAPIDCONNECT_E2E
    • EMV_A35_HEARTLAND
    • EMV_A35_DATACAP_E2E
    • EMV_A35_EVO
    • EMV_IM30_EVO
  • For Ingenico devices, the left 4 characters of the kernel version is now checked rather than the entire kernel version field returned in the 07. command response.
  • Previously, the IDTech VP6800 would quickly flash “Canceled” during a PadReset. This message has been removed.
  • This version of dsiEMVUS allows the new VoidByInvoiceNo transaction to be passed through to NETePay. The VoidByInvoiceNo trancode does not collect card data.
  • The IDTech VP3300 whitelist is now enabled during the end of an EMVParamDownload. It is expected that an ISV will perform an EMVParamDownload rather than a dsiPDCX SecureDeviceInit which also loads the whitelist for the VP3300.
Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

dsiPDCX® 1.85

Release date: 11/14/2022

Datacap’s out-of-scope ActiveX control for NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers.

Release notes for v1.85

  • Support is added for the PAX A35. Also, the PAX IM30 for EVO is released now that we have a full certification for this unattended device. New SecureDevice values listed below...
    • PAXA35
    • PAXA35_DATACAP_E2E
    • PAXA35_VANTIV_E2E
    • PAXA35_EVO_E2E
    • PAXA35_RAPIDCONNECT_E2E
    • PAXA35_TSYS_VOLT
    • PAXA35_HEARTLAND_VOLT
    • PAXIM30_EVO_E2E
  • This version of dsiEMVUS allows the new VoidByInvoiceNo transaction to be passed through to NETePay. The VoidByInvoiceNo trancode does not collect card data.
Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro
Step 2 - Install NETePay FDMS Rapid Connect Host EMV - RRH 5.06.16 Rental

Release date: 09/11/2017

  • Support added for eCommerce merchant category.
  • POSEntryMode on EMV fallback to manual changed from "79" to "01" to resolve an issue where all keyed Visa transactions routed to Buypass were declined.
Microsoft Windows 10 Pro / 8 Pro / 7 Pro (Windows XP and Vista do not support TLS 1.2 which is now an industry requirement)