Please follow the steps below to complete your installation of NETePay EVO US EMV (FD-RC) Host - RRH 5.06.12 Rental

Step 1 - Install Client Control

In order to communicate with this NETePay your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.75

Release date: 12/05/2023

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our Compatible devices page.

Release notes for v1.75

  • Support is added for Pax A800 devices. This device is similar to the Pax A920PRO except that the MSR is on the side rather than the top. New SecureDevice values are below.
    • EMV_A800_PAYMENTECH
    • EMV_A800_VANTIV_E2E
    • EMV_A800_TSYS
    • EMV_A800_TSYS_VOLT
    • EMV_A800_RAPIDCONNECT
    • EMV_A800_RAPIDCONNECT_E2E
    • EMV_A800_HEARTLAND
    • EMV_A800_DATACAP
    • EMV_A800_DATACAP_BLUEFIN
    • EMV_A800_EVO
  • Support is added for the IDTech VP3350. The VP3350 supports tap, chip and swipe, credit only. This release supports the VP3350 with the Datacap TDES PAN key. The new SecureDevice value is below.
    • EMV_VP3350_DATACAP_E2E
    • For Verifone P400 devices, this version explicitly disables the U01 command – external AID selection. The next version will enable the U01 command. This will allow an ISV to move back to this version if there is an issue with the U01 command in next release.
Microsoft Windows 11 Pro / 10 Pro / Server 2019 / Server 2016

OR

dsiPDCX® 1.90

Release date: 12/05/2023

Datacap’s out-of-scope ActiveX control for NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers.

Release notes for v1.90

  • Support is added for Pax A800 devices. The A800 is similar to the A920PRO except that the MSR is on the side rather than the top. The PAX devices support Credit, Debit, EBT and PrePaid. New SecureDevice values are below.
    • PAXA800
    • PAXA800_DATACAP_E2E
    • PAXA800_DATACAP_BLUEFIN
    • PAXA800_VANTIV_E2E
    • PAXA800_EVO_E2E
    • PAXA800_RAPIDCONNECT_E2E
    • PAXA800_TSYS_VOLT
    • PAXA800_HEARTLAND_VOLT
  • Support is added for the IDTech VP3350. This release supports the VP3350 with the Datacap TDES PAN encryption. The VP3350 supports swipe, Credit and PrePaid only. It supports GetPrePaidStripe and GetPrePaidStripeAllTracks, but it does not load a whitelist. The new SecureDevice value is below.
    • IDTVP3350_DATACAP_E2E
  • For Pax MSR read failures, retry logic is added.
  • For Verifone P400, keyed clear EBT account numbers are allowed even when a device in encrypted. Swiped clear EBT account numbers are also allowed when a device is encrypted.
  • For Ingenico Lane/8000 clear device, the value is fixed for SecureDeviceInit. Earlier versions returned Invalid Pad Type.
Microsoft Windows 11 Pro / 10 Pro / Server 2019 / Server 2016

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software.

Microsoft Windows 11 Pro / 10 Pro / Server 2019 / Server 2016
Step 2 - Install NETePay EVO US EMV (FD-RC) Host - RRH 5.06.12 Rental

Release date: 07/12/2016

Support is added for an EMV PreAuth transaction and PreAuthCaptureByRecordNo (with token). These two new transactions have been added since Rapid Connect does not support an Adjust transaction to add a TIP after the initial authorization (Sale). Restaurant systems need to make an integration change to support the EMV PreAuth and subsequent PreAuthCaptureByRecordNo transaction. The PreAuth must be captured in order for the transaction to be settled. The PreAuthCaptureByRecordNo must be performed only once since it captures a transaction to the current batch. The TIP amount may be zero. If a mistake occurs with the amount captured, the integration must use a VoidSaleByRecordNo to remove the transaction from the batch. The dsiEMVUS Integration Spec has been revised to add these two new transactions. The document version is now V02.13.

Microsoft Windows 11 Pro / 10 Pro / Server 2019 / Server 2016