Please follow the steps below to complete your installation of NETePay Heartland Portico Host EMV - HRH 5.06.11 Rental

Step 1 - Install Client Control

In order to communicate with this NETePay your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.17

Release date: 08/10/2017

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our PC based POS solutions page.

Release notes for v1.17

  • Support added for the following devices with Paymentech.
    • Ingenico iSC250
    • Ingenico iPP320
    • Ingenico iPP350
    • Ingenico iCMP
    • Ingenico iSC480
  • Support added for the following devices using TDES DUKPT P2PE with BluePay.
    • Ingenico iSC250
    • Ingenico iPP320
    • Ingenico iPP350
    • Ingenico iCMP
    • Ingenico iSC480
  • Quick Chip support added for Equinox L5200 and L5300 pads when using Mercury or Paymentech.
  • Quick Chip support added for Ingenico devices running RBA 21 with EMV Kernel 0467. Please keep in mind that this is not a standard load and RBA 21 is typically packaged with EMV Kernel 0526 which will not work with dsiEMVUS v1.17.
  • A few "usability" changes are included for the IDTech devices. Please note that this version of dsiEMVUS requires ID TECH devices have at least firmware version 1.01.012 loaded.
  • Correction to Ingenico contactless settings to allow Discover Zip contactless MSD transactions.
  • Selection of SecureDevices in the EMV US Client Test application is now done via a list box instead of raido buttons.

New build 8/24/17 - Change to EMVParamDownload for ID TECH devices to suppress the inclusion of LRC with Track2 data. Status dialog displayed for ID TECH devices where DisplayMessage event is not subscribed to and window handle not passed in on request.

New build 9/27/17 - Changes related to Paymentech confidence testing.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

dsiPDCX® 1.49

Release date: 08/09/2017

Datacap’s out-of-scope ActiveX control for NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers.

Release notes for v1.49

  • Support added for the following devices using TDES DUKPT P2PE with BluePay.
    • Ingenico iSC250
    • Ingenico iPP320
    • Ingenico iPP350
    • Ingenico iCMP
    • Ingenico iSC480

New build 8/30/17 - Fix for ID TECH SecureDeviceInit

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro
Step 2 - Install NETePay Heartland Portico Host EMV - HRH 5.06.11 Rental

Release date: 05/04/2016

A new “EMV Cardholder Verification” parameter is added to this NETePay where the choices are “All CVMs”, “Signature” or “None”. “All CVMs” is the default on PSCS and includes Online PIN, Offline PIN, Signature and No CVM. This setting in NETePay determines the “EMV Terminal Capabilities” setting stored in the PIN pad during an EMV Parameter Download operation. If this parameter is changed in NETePay, then an EMV Parameter Download should be run at each workstation where a PIN pad is attached.

New build released 7/24/17 - Changes made to data sent on EMVZeroAuth.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro