Please follow the steps below to complete your installation of NETePay Worldpay IP (Mercury) US EMV - MPH 5.06.11

Step 1 - Install Client Control

In order to communicate with this NETePay your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.37

Release date: 10/11/2019

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our PC based POS solutions page.

Release notes for v1.37

  • Support is added for the IDTech VP3300 device for Mercury. Supports chip and swiped cards with Mercury PAN encryption. SecureDevice values is "EMV_VP3300_MERCURY".
  • Support is added for Ingenico Telium Devices for First Data Rapid Connect supporting OnGuard PAN encryption. This is required for First Data’s Validated P2PE. The following SecureDevice values were added.
    • EMV_ISC250_RAPIDCONNECT_ONGUARD
    • EMV_IPP350_RAPIDCONNECT_ONGUARD
    • EMV_IPP320_RAPIDCONNECT_ONGUARD
    • EMV_ICMP_RAPIDCONNECT_ONGUARD
    • EMV_IUC285_RAPIDCONNECT_ONGUARD
    • EMV_ISC480_ RAPIDCONNECT_ONGUARD
    • EMV_IUP250_RAPIDCONNECT_ONGUARD
    • EMV_ISMP4_RAPIDCONNECT_ONGUARD
    • EMV_IWL258_RAPIDCONNECT_ONGUARD
  • "ProcessEasyCheckout()" method is added for integration to Datacap’s EasyCheckout Application.
  • For Verifone Vx805 XPI 12 over IP, wait times are increased for ACKs and reboot so that an EMVParamDownload will return "Success".
  • For Ingenico devices, the maximum cash back amount for Debit is increased from $100.00 to $999.99.
Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

dsiPDCX® 1.63

Release date: 10/10/2019

Datacap’s out-of-scope ActiveX control for NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers.

Release notes for v1.63

  • Support is added for the IDTech VP3300 device for Mercury. Supports swiped cards with Mercury PAN encryption. Its SecureDevice value is IDTVP3300_MERCURY_E2E.
  • Support is added for Ingenico Telium Devices for First Data Rapid Connect supporting OnGuard PAN encryption. This is required for First Data’s Validated P2PE. Corresponding SecureDevice values are as follows.
    • INGENICOISC250_RAPIDCONNECT_ONGUARD
    • INGENICOIPP350_RAPIDCONNECT_ONGUARD
    • INGENICOIPP320_RAPIDCONNECT_ONGUARD
    • INGENICOICMP_RAPIDCONNECT_ONGUARD
    • INGENICOISC480_RAPIDCONNECT_ONGUARD
    • INGENICOISMP4_RAPIDCONNECT_ONGUARD
Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro
Step 2 - Install NETePay Worldpay IP (Mercury) US EMV - MPH 5.06.11

Release date: 11/18/2015

Enhanced to support multiple card verification methods (CVMs).

  • Build 0001 released 1/13/17
    • Support for Smart Updates which allows NETePay to be automatically updated to its versions most currently build.
    • Support for being run as a service. Please review this NETePay's userguide for details on configuring this feature.
Microsoft Windows 10 Pro / 8 Pro / 7 Pro (Windows XP and Vista do not support TLS 1.2 which is now an industry requirement)